반응형 Cluster10 Juniper SRX Cluster configuration - Node 0 # set chassis cluster cluster-id 1 node 0 reboot - Node 1 # set chassis cluster cluster-id 1 node 1 reboot set groups node0 system host-name srx1500-1 set groups node0 interfaces fxp0 unit 0 family inet address 192.16.35.46/24 set groups node1 system host-name srx1500-2 set groups node1 interfaces fxp0 unit 0 family inet address 192.16.35.47/24 set groups node0 system backup-rout.. 2021. 8. 26. Gigamon Clustering #2 Cluster B 5.9.00TA10 [1717: normal] (config) # show running-config #### Running database "initial"## Generated at 2021/04/28 16:50:40 +0900## Software version on which this output was taken: GigaVUE-OS 5.9.00 172922 2020-04-01 08:04:02## Hostname: TA10#### Note: If you are not an admin user some command invocations may be omitted## because you do not have permissions to see them.###### Network i.. 2021. 6. 11. Gigamon Clustering #1 Cluster A 5.9.00wins-gigamon [1717: master] (config) # show running-config #### Running database "20210428_backup"## Generated at 2021/04/28 16:51:51 +0900## Software version on which this output was taken: GigaVUE-OS 5.9.00 172922 2020-04-01 08:04:52## Hostname: wins-gigamon#### Note: If you are not an admin user some command invocations may be omitted## because you do not have permissions to s.. 2021. 6. 11. Juniper SRX request chassis cluster failover redundancy-group Juniper SRX request chassis cluster failover redundancy-groupdate_range22-Feb-21arrow_backward arrow_forwardSyntaxcontent_copy zoom_out_maprequest chassis cluster failover node node-number redundancy-group redundancy-group-numberDescriptionFor chassis cluster configurations, initiate manual failover in a redundancy group from one node to the other, which becomes the primary node, and automatical.. 2021. 4. 13. Cluster B Cluster BHC2B [1717: standby] (config) # show running-config #### Running database "initial"## Generated at 2019/12/02 06:00:48 +0000## Software version on which this output was taken: GigaVUE-OS 5.7.01 142718 2019-09-23 23:23:16## Hostname: HC2B###### Network interface configuration##interface eth1 create exitinterface inband create exitinterface eth0 no dhcp ip address 10.10.7.153 /24 e.. 2020. 6. 3. Cluster A Cluster AHC2A [1717: master] (config) # show running-config #### Running database "initial"## Generated at 2019/12/02 05:57:30 +0000## Software version on which this output was taken: GigaVUE-OS 5.7.01 142718 2019-09-23 23:23:16## Hostname: HC2A###### Network interface configuration##interface eth1 create exitinterface inband create exitinterface eth0 no dhcp ip address 10.10.7.152 /24 ex.. 2020. 6. 3. FortiSandbox Cluster Example configurationThis example shows the steps for setting up an HA cluster using three FortiSandbox 3000D units.Step 1 - Prepare the hardwareThe following hardware will be required:l Nine cables for network connectionsl Three 1/10 Gbps switchesl Three FortiSandbox 3000D units with proper power connections (units A, B, and C).The master and primary slaves should be on different power circuits.. 2018. 5. 8. FortiSandbox Clustering Setting FortiSandbox Clustering Setting Step 1 - Configure the master1. Configure the port IP addresses and gateway address with the following commands:set port1-ip 192.168.1.99/24set port2-ip 192.168.2.99/24set port3-ip 192.168.3.99/24set default-gw 192.168.1.12. Configure the device as the master node and its cluster fail-over IP for Port1 with the following commands:hc-settings -sc -tM -nMasterA -cTe.. 2017. 8. 8. [Linux] Linux Cluster Overview Linux Cluster Overview[ 목 차 ]1. 클러스터2. 클러스터의 필요성3. 클러스터의 종류 3-1. 고계산용 클러스터 (HPC) 3-2. 부하분산 클러스터 (LVS) 3-3. 고가용성 클러스터 (HA) 3-4. 그외의 클러스터 분류4. 클러스터의 단점 1. 클러스터 컴퓨팅 파워를 증가시키기 위한 다양한 방법이 있다. 그중 고성능 단일 컴퓨터를 이용한 계산은 이미 그 한계가 있음이 증명된 상태이며 이의 대안으로 다수의 프로세서(CPU)가 하나의 문제를 협동적으로 계산하는 병렬컴퓨팅이 등장하게 되었다. 다수의 프로세서가 하나의 메모리를 공유하는 SMP(symmetric multiprocessing) 머신, 다수의 프로세서가 각각 독립된 메모리를 가지고 있는 MPP(massive.. 2012. 10. 18. 이전 1 2 다음 반응형
